|
|
|
|
|
|
Torlon
4503
|
Torlon
4203
|
Torlon
4203L
|
Torlon
4501
|
Torlon
4301
|
Torlon
4301
|
Torlon
5530
|
Torlon
5030
|
|
|
|
|
Units
|
ASTM
Test Method
|
Compression
Molded Polyamideimide
|
Extruded
Polyamideimide
|
Injection
Molded Polyamideimide
|
Compression
Molded Bearing Polyamideimide
|
Extruded
Bearing Grade Poly-amideimide
|
Injection
Molded Bearing Polyamideimide
|
Compression
Molded 30% GF Polyamideimide
|
Injection
Molded 30% GF Polyamideimide
|
|
MECHANICAL
|
1
|
Strength
to Weight Ratio
|
ksi
|
-
|
|
|
|
|
|
|
|
|
|
2
|
Specific
Gravity @73 F
|
-
|
D792
|
1.40
|
1.41
|
1.41
|
1.45
|
1.45
|
1.45
|
1.61
|
1.60
|
|
3
|
Tensile
Strength @73 F, (ult)/(yld)
|
psi
|
D638
|
18000
(ult)
|
18000
(ult)
|
22000
(ult)
|
10000
(ult)
|
12000
(ult)
|
19000
|
14000
(ult)
|
24000
(ult)
|
|
4
|
Tensile
Modulus of Elasticity @ 73 F
|
psi
|
D638
|
500000
|
600000
|
600000
|
440000
|
900000
|
760000
|
500000
|
1200000
|
|
5
|
Tensile
Elongation at Break @ 73 F
|
%
|
D638
|
5
|
5
|
15
|
3
|
3
|
7
|
3
|
4
|
|
6
|
Flexural
Strength @ 73 F
|
psi
|
D790
|
24000
|
24000
|
28000
|
20000
|
31000
|
25000
|
20000
|
36000
|
|
7
|
Flexural
Modulus of Elasticity @ 73 F
|
psi
|
D790
|
600000
|
600000
|
700000
|
650000
|
1000000
|
750000
|
800000
|
1000000
|
|
8
|
Shear
Strength @ 73 F
|
psi
|
D732
|
-
|
16000
|
15000
|
-
|
16400
|
13000
|
-
|
24500
|
|
9
|
Compressive
Strength, (% Deformation) @73 F
|
psi
|
D695
|
17000
(10)
|
28000
(10)
|
32000
(10)
|
18000
(10)
|
24000
(10)
|
24000
(10)
|
18000
(10)
|
38000
(10)
|
|
10
|
Compressive
Modulus of Elasticity @73 F
|
psi
|
D695
|
350000
|
700000
|
700000
|
350000
|
950000
|
950000
|
350000
|
600000
|
|
11
|
Hardness,
Rockwell, Scale as noted @73 F
|
-
|
D785
|
M119
(E80)
|
M120
(E80)
|
M120
(E80)
|
M106
(E70)
|
M106
(E70)
|
M106
(E70)
|
M120
E77)
|
M125
(E77)
|
|
12
|
Hardness, Durometer,
Shore D @73 F
|
-
|
D2240
|
D90
|
-
|
-
|
D90
|
-
|
-
|
D90
|
-
|
|
13
|
Izod
Impact, (Notched) @73 F
|
ft-lb/in
of notch
|
D256
TypeA
|
1.5
|
2.0
|
2.5
|
0.5
|
0.8
|
1.1
|
0.7
|
1.3
|
|
14
|
Coefficient
of Friction, (Dry vs. Steel) Dynamic
|
-
|
-
|
0.30
|
0.27
|
0.35
|
0.20
|
0.20
|
0.20
|
0.20
|
0.19
|
|
15
|
Limiting
PV, (with 4 to 1 factor of safety applied)
|
psi-ft/min
|
-
|
-
|
17500
|
-
|
22500
|
22500
|
30000
|
20000
|
-
|
|
THERMAL
|
16
|
Coefficient
of Linear Thermal Expansion @73 F
|
in/in/F
|
E-831
(TMA)
|
1.5E-05
|
1.7E-05
|
1.7E-05
|
2.0E-05
|
1.4E-05
|
1.4E-05
|
2.5E-05
|
1.0E-05
|
|
17
|
Heat
Deflection Temperature @ 264 psi
|
F
|
D648
|
532
|
532
|
532
|
534
|
534
|
534
|
520
|
539
|
|
18
|
Tg-Glass
transition temperature, (Amorphous)
|
F
|
D3418
|
527
|
527
|
527
|
527
|
527
|
527
|
527
|
527
|
|
19
|
Melting
Point, (VS=Vicat Softening Temp.)
|
F
|
D3418
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
|
20
|
Continuous
Service Temperature in Air, (Max.)
|
F
|
-
|
500
|
500
|
500
|
500
|
500
|
500
|
500
|
500
|
|
21
|
Thermal
Conductivity
|
BTU-in/hr-ft2-F
|
-
|
1.80
|
1.80
|
1.80
|
3.70
|
3.70
|
3.70
|
2.50
|
2.50
|
|
ELECTRICAL
|
22
|
Dielectric
Strength, Short Term
|
Volts/mil
|
D149
|
580
|
580
|
580
|
-
|
-
|
-
|
700
|
840
|
|
23
|
Volume
Resistivity
|
ohm-cm
|
D257
|
2.0E+17
|
2.0E+17
|
2.0E+17
|
8.0E+15
|
3.0E+15
|
8.0E+15
|
2.0E+17
|
2.0E+17
|
|
24
|
Dielectric
Constant @ 10E6 Hz
|
-
|
D150
|
3.9
|
3.9
|
3.4
|
5.4
|
6.0
|
5.4
|
6.3
|
6.5
|
|
25
|
Dissipation
Factor @ 10E6 Hz
|
-
|
D150
|
0.031
|
0.031
|
0.031
|
0.042
|
0.037
|
0.042
|
0.220
|
0.023
|
|
26
|
Flammability @
3.1 mm unless noted
|
-
|
UL94
|
V-O
|
V-O
|
V-0
|
V-0
|
V-0
|
V-0
|
V-0
|
V-0
|
|
H2O
|
27
|
Water
Absorbtion, Immersion, 24 Hrs
|
%
by wt.
|
D570(7)
|
0.35
|
0.40
|
0.33
|
0.30
|
0.28
|
0.28
|
0.30
|
0.30
|
|
28
|
Water
Absorbtion, Saturation
|
%
by wt.
|
D570(7)
|
1.70
|
1.70
|
1.70
|
1.50
|
1.50
|
1.50
|
1.50
|
1.50
|
